Buy P3ICP/2500BAR from Hbm in Paraguay

1-SUBHD15-MALE

connector kit

1-T4WA-S3/10NM

HBM Schraubmesswelle, nominal torque 10 Nm with strain gauge measuring system, accuracy class 0.1 built-in rotary encoder Tool Standard connections 10 F / G 10 according to DIN 3121 with 2 fixed mounted connection cables separately for torque u. angle of rotation 3 m long, with free ends

1-T5/20NM

Torque transducer, rated torque 20 NmMesssignalübertragung about SchleifringeDMS measurement system accuracy: 0.1Elektrischer connection via plug introduction of torque on shaft stub (friction) torque output signal 2mV / VNenndrehzahl 4000U / min

1-TB1A/100NM

Torque reference sensor

1-TB1A/5KNM

Reference torque measuring disc, nominal torque 5 kNm DMS measuring system Accuracy class: 0.05 Permanently mounted connection cable 3m, with free ends Torque transmission via flange Torque output signal 1.5mV / V

1-WA/100MM-T

displacement transducer

1-WS/ZB 12 ALTERNATIF

Mitutoyo Mark Magnetblock HBM can not be produced

1-X60-NP

1-Z6FC3/50KG-1

(load cell Rated load: 50kg Minimum division value: 0.0090% of Emax OIML R60 test report Accuracy: C3 Measuring body: Stainless steel Protection: IP68 according to EN 60529 Cable: Shielded 6-wire round cable with PVC Cable length: 3m)

3-3312.0182

SUB-D-Stecker

C2/50KN

compressive force transducer

D-15D/MONT

D-MONT

Anschlussstecker

DQ809

8-channel USB measurement amplifier espressoDAQFamilie

D-TEDS/MONT-DB

including programming the memory contents of the TEDS TEDS Aufnehmersteck module is mounted.

HLC-40KN

Type HLM-20242 Output 1.8 millivolts load cell

HLCB1C3 1,1

Emax: 2.2 t, Emin: 0 kg, Limit: 3.3 t Vmin: 220 g, Cn; 1.94 mv/v; TC2163

HLCB1C3/4.4T

Load cell

K-CAL-F-D-7-B-S-S

(Calibration of the measured variable force in accordance with the HBM standard (without connector assembly). Traceability by DAkkS accreditation guaranteed by ISO 17025 or at factory calibrations (WCS) in Reference to ISO 10012 Calibration certificate in German and English Calibration type force DAkkS ISO 376, 8 steps Calibration power <= 1 MN Of load power tension and compression Number of measuring bridges Power Easy Bridge TEDS TEDS programming without programming)

K-CAL-T-W-1-B-S-S-2-0

Calibration of the measured variable torque according HBM standard (Without connector or coupling assembly. Traceability through accreditation ISO 17025 (DKD) guarantees In DAkkS / DKD - calibrations optionally by: DIN 51309, EURAMET / cg-14, VDI2646 (Teilbereichskal. Not possible) DKD-R 3-5 (turning moment), or DKD-R 3-7 (transfer torque wrench). Factory calibrations (WCS) in relation to ISO 10012th Calibration certificate in German and English Calibration type torque WKS, 6 steps, 1 + 1 measurements Measuring range <= 200Nm Load direction right and left Moment Number outputs an output signal TEDS TEDS programming without programming 1. Signal output mV / V 2. Signal output 0

K-CAL-T-W-5-B-S-S-2-0

Calibration of the measured variable torque according HBM standard (Without connector or coupling assembly. Traceability through accreditation ISO 17025 (DKD) guarantees In DAkkS / DKD - calibrations optionally by: DIN 51309, EURAMET / cg-14, VDI2646 (Teilbereichskal. Not possible) DKD-R 3-5 (turning moment), or DKD-R 3-7 (transfer torque wrench). Factory calibrations (WCS) in Terms of ISO 10,012th Calibration certificate in German and English Calibration type torque WKS, 6 steps, 1 + 1 measurements Measuring range <= 10kNm Load direction right and left Moment Number outputs an output signal TEDS TEDS programming without programming 1. Signal output mV / V

K-LY41-1,5/350

K-LY41-6/350

K-LY43-3/120-3-7.5M

technology özllkler ksmnda blgi was

K-P3-MB-200B-Y  

Absolute Pressure Measuring system: strain gauge 350 Ohm

K-RTN-S-C3-150-N-12-N-N-S-S

(K-RTNaa / bbb cccc dd eee Compact RTN load cell as a variant in special design DMS-measuring system (4000 ohms), nominal characteristic value 2.85 mV / V, with fixed cable, free ends, IP68 protection to EN 60,529th design standard Accuracy class C3 Rated load 150t Explosion protection No explosion Cable length 12m Others without TK0 without Country / customer default Creep 20 ° C Standard)

K-RY81-1,5/350

3-way rosette 1.5, 350 OHM LUK / SENSOR / 3Set floors form

K-RY81-3/350